End-to-end fire protection and engineering solutions · Pioneers since 1978

System fault or discharge? Emergency response

Annual maintenance contracts

Documented proof that every system on site is ready to work.

A WATERWEB annual maintenance contract (AMC) covers the inspection, testing and maintenance of every fire protection system on site, with graded deficiency reports, impairment management and the records that fire authorities and insurers expect.

Overview

Fire protection systems may stand idle for years, yet they must work the first time they are called upon. Over that period, valves are closed for works, sprinklers are painted or obstructed, batteries age, pumps lose performance and buildings change around the systems designed to protect them.

Most failures stem from how systems are managed, not from the equipment. A structured maintenance programme identifies these conditions early, grades them by their effect on performance and ensures they are corrected. It also builds a documented record of compliance for fire authority inspections, no-objection certificate (NOC) renewals and insurance surveys.

57%

of sprinkler failures occurred because the system had been shut off, the largest single cause identified.

Source: National Fire Protection Association (NFPA), U.S. Experience with Sprinklers, 2021
Illustration of a technician checking a fire pump against a maintenance schedule

How it works

Every contract begins with a condition survey that establishes a documented baseline. WATERWEB then agrees a schedule of weekly, monthly, quarterly and annual tasks drawn from the governing Indian Standards and, where specified, NFPA 25 and NFPA 72. Each visit produces a report that grades every finding by severity, from non-critical deficiency to impairment, cites the governing clause and proposes a remedy.

Contract deliverables

ITM schedule
A site-specific calendar of inspection, testing and maintenance (ITM) tasks.
Service reports
Test results for every system, device and pump, with photographic evidence.
Deficiency register
Findings graded by severity, with clause references and remedial proposals.
Impairment management
Procedures and notifications while any system is out of service.
Pump performance records
Flow test results tracked against the original performance curve.
Annual compliance summary
A consolidated record for fire authority, NOC and insurer files.

How findings are graded

GradeDefinition
Non-critical deficiencyDoes not affect fire performance but falls short of the standard, such as missing valve signage.
Critical deficiencyCould affect performance in a fire, such as obstructed or painted sprinklers.
ImpairmentA system or part of a system out of service, such as a closed control valve or a pump that will not start.

Programme principles

Code-referenced findings

Every finding tied to the governing clause, so priorities are objective.

Risk-based escalation

Critical deficiencies and impairments escalated immediately, not held for the next report.

Minimal disruption

Testing planned around production, occupancy and shutdown windows.

Multi-system coverage

Hydrants, sprinklers, detection, suppression and extinguishers under one contract.

Transparent records

Documentation structured for auditors, fire officers and insurers.

Lifecycle planning

Advance notice of components approaching the end of their service life.

Typical applications

  • Any building or facility with installed fire protection systems
  • Ahead of a fire NOC renewal or biennial inspection
  • Where the insurer requires documented maintenance records
  • When replacing an incumbent maintenance contractor

Visit frequency is set by the governing code, the insurer and the systems installed.

Scope of delivery

  1. Condition survey

    Every system inspected and deficiencies recorded before the contract begins.

  2. Schedule

    Weekly, monthly, quarterly and annual tasks agreed for the site.

  3. Service visits

    Tests performed and recorded against the agreed schedule.

  4. Reporting

    A written report after every visit and an annual compliance summary.

  5. Breakdown support

    Priority response to system faults within 72 hours.

Owner responsibilities

Most inspection findings trace back to simple checks missed between service visits. The items below fall to the owner; every WATERWEB maintenance report adds the checks specific to the site.

  • Nominate a single point of contact on site
  • Complete the weekly checks in the site logbook
  • Provide access to pump houses, risers and roofs on service days
  • Approve remedial works graded as critical without delay

Frequently asked questions

What does an AMC visit include?

Scope depends on the installed systems and the visit frequency. A typical quarterly visit covers pump runs, valve checks, detector and call point testing, extinguisher inspection and a written report.

Does WATERWEB maintain systems installed by other contractors?

Yes. Every engagement begins with a condition survey, which sets an agreed baseline before WATERWEB takes responsibility for the system.

What happens when a system is impaired?

WATERWEB notifies the site contact immediately, tags the impaired system and advises on interim measures, such as a fire watch, until the system is restored and verified.

How is an AMC priced?

Pricing reflects the installed systems, their scale and the visit frequency. [Indicative price ranges to add].

Planning a new facility, or assessing an existing system?

A WATERWEB engineer will review your drawings or survey the site, assess it against the governing code and set out recommendations in writing.

CallWhatsApp